<ins id="5wker"><ol id="5wker"></ol></ins>
        <strong id="5wker"></strong>
        <strong id="5wker"><u id="5wker"></u></strong>
        <strong id="5wker"><u id="5wker"></u></strong>
        <ins id="5wker"><ol id="5wker"><pre id="5wker"></pre></ol></ins>
        <strong id="5wker"></strong>
        <ins id="5wker"></ins>
          <strong id="5wker"><u id="5wker"><button id="5wker"></button></u></strong>
              <strong id="5wker"></strong>
              <strong id="5wker"><u id="5wker"></u></strong>
                <ins id="5wker"><u id="5wker"></u></ins>
                <strong id="5wker"><u id="5wker"></u></strong>
                <strong id="5wker"></strong>

                  专业的煤气发生炉厂家!郑州科能机械制造有限公司欢迎您!

                  郑州科能机械制造有限公司

                  郑州科能机械制造有限公司联系方式
                  行业资讯

                  两段式煤气发生炉煤焦油的储存方法Treatment of coal tar in two - stage gas producer

                    两段式煤气发生炉煤焦油的储存方法:

                      1、一种贮存办法就是建一个地下焦油池,在焦油池内敷设蒸汽加热管,保持一定的油温,然后由焦油泵将其打入室外焦油池。地下焦油池的蒸汽排管的材质及安装质量要求较高,因为一旦损坏,由于排尽剩留焦油实属不易,所以多数要依靠人工挖取。

                      2、再有就是件一个具有一定容积的露天焦油池,焦油流入后自行固化至逐渐硬化。

                      3、近几年比较流行的一种方法就是建一个焦油罐,焦油罐内贮存一般是通过压力罐输送到其中,或者是从地下油池经焦油泵打入其中。焦油罐不仅有贮存作用,而且还有脱水作用,因为含水的焦油一般在85~90℃贮存,很容易使焦油水混合物进行分离,由于气化焦油的比重大于1,所以被分离出来的水浮于水面,一般经24小时加热贮存,焦油的脱水率可以达到80%以上。所以在焦油管中不但应设置足够用量的加热排管,而且还应有分离水的不同高度的排水管。

                      煤气发生炉煤气的输送操作规程:

                      1、首先打开受热设备的烟道阀门,再打开需点火的煤气阀门、空气阀门。先开一个烧嘴。

                      2、打开煤气炉水封,让煤气送入加热炉。

                      3、当煤气从烧嘴出来时,用点燃的火把放至加热炉烧嘴进行点火。若一次点火不成,必须将废气排除后再进行送气,逐个烧嘴点火。

                      4、烧嘴着火后,启动一次风机,进行空气助燃。

                      5、根据受热设备加热的工艺要求,调节煤气量及风量,使温度达到工艺要求。

                      本公司可以现场加工煤气发生炉、煤气发生炉的安装、调试,煤气发生炉疑难问题的处理等,价格合理,质量优。联系电话:86-13676907460

                  Storage method of coal tar in two-stage gas producer:

                  1. One method of storage is to build an underground tar pool, in which steam heating pipes are laid to maintain a certain oil temperature, and then the coke pump drives it into the outdoor tar pool.The material of the steam exhaust pipe of underground tar pool and installation quality requirement are higher, because once damaged, because exhausted remaining tar is really not easy, so most to rely on manual excavation.

                  2, there is a certain volume of an open tar pool, the tar into the curing to gradually harden.

                  3. In recent years, a popular method is to build a coke oil tank. The storage of tar tank is usually delivered to it by pressure tank or pumped into it by coke oil pump from underground oil tank.Coke tank not only has storage effect, but also the dewatering effect, because the tar is in commonly 85 ~ 90 ℃ water storage, it is easy to make the tar water mixture separation, because the proportion of gasification tar is greater than 1, so the water is separated out floating on the surface of the water, generally after 24 hours heating storage, tar dehydration rate can reach more than 80%.So in the tar pipe should be set not only sufficient amount of heating pipe, but also should be separated from the water at different heights of the drainage pipe.

                  Operating rules for the transportation of gas from gas producer:

                  1. First open the flue valve of heating equipment, and then open the gas valve and air valve to be ignited.Open a burner first.

                  2, open the gas stove water seal, let the gas into the heating furnace.

                  3. When the gas comes out of the burner, put the torch into the burner of the heating furnace for ignition.If a ignition is not, the exhaust gas must be removed before the air, one by one burner ignition.

                  4. After the burner is on fire, start the fan for air combustion.

                  5. According to the technological requirements of heating equipment, adjust the gas quantity and air quantity to make the temperature reach the technological requirements.

                  The company can process the on-site gas generator, gas generator installation, debugging, gas generator difficult problems, such as the treatment of gas generator, reasonable price, excellent quality.Contact number: 86-13676907460

                     



                     


                  上一篇:河南二手球磨机 下一篇:没有了
                  ?
                  ?